Do You Need to Reseal Drywall Again if Days Have Passed Since First Coat Before Painting

Starting time, you blench—a natural reaction to that tiny ding on a relatively new paint job—and then you lot shrug. Some paint imperfections, however, are more conspicuous and harder to overlook. Such problems must exist addressed, the sooner the ameliorate, not only to restore the painted surface but to investigate potential underlying problems.

Read on to understand the causes of common paint problems and how to repair them and avoid future problems.

Bang-up, Flaking, and Clumping

Vein-like lines that appear through at least i coat of pigment may be faint initially, but these cracks tend to abound and deepen into dry out, jagged flakes. Such unsightliness can strike a diversity of surfaces, indoors and out, from plaster to wood and siding.

What causes paint to scissure?

Bereft surface prep is the primary culprit behind scissure attacks. Over-thinning your paint or applying it too thinly can as well cause it to split.

Conversely, a heavy mitt while painting tin atomic number 82 to what's chosen mud cracks, where too-thick paint dries with a clumpy, swollen look. Not allowing adequate dry fourth dimension betwixt coats tin can also lead to these problems. And unfortunately, cracks can appear merely due to age. Over time, paint becomes breakable, making information technology less adaptable to temperature and humidity fluctuations.

Repair and Prevention

If damage is extensive, you may need to repaint the entire surface. If not, with the right technique, you can repair a poorly painted spot without a lot of headache. Follow the tips detailed below for solutions.

1. Remove all cracked and flaking pigment with a scraper, wire brush, heat gun, or chemical application (depending on the extent and severity of the problem).
2. Sand, feathering the edges to blend, then clean and prime the surface.
3. Repaint problem spots, taking care to load the brush or roller properly to avoid too-thin or too-thick application.
4. For brush awarding, dip the brush in, allowing pigment to encompass up to i-third of the bristle length; tap the brush lightly on both sides and avoid dragging the brush against the edge of the container.
5. If using a roller, fill the roller tray halfway. Remove lint from a new roller embrace, dip the roller into the well of the tray, and so over the ribbed portion of the tray, repeating several times to evenly distribute the right amount of pigment.

To avoid heavy buildup in corners where paint commonly overlaps, thoroughly feather out the cutting-in area; then clean and prep, reapplying paint evenly. And be patient, always remembering to let paint dry out fully between coats. When repainting to repair, you lot'll likely want to apply the same product you lot used initially (but in subsequent projects, opt for quality latex paint, known for its adhesion and flexibility).

Peeling

Peeling paint that has a bit of curl to it is a common problem on both interior and exterior surfaces.

What causes pigment to peel?

While improper prep and application can contribute to peeling, moisture is public enemy number one.

1. Inside the home, excessive moisture may come up from loftier humidity in the basement and/or foundation, just fifty-fifty zealous showering, cooking, and humidifier habits can be to arraign.
2. Outside the house, peeling can effect from inadequate caulking, clogged gutters, a leaky roof, or interior moisture that seeps through outside walls. Peeling can also occur if paint is practical to a damp surface or to siding that's less than vi inches above the ground.

Repair and Prevention

Watch: Repairing Peeling Pigment

Create a less pare-prone surround inside and out by implementing the following recommendations.

Better interior ventilation as needed with frazzle fans, wall vents, and/or louvers.

For exterior conditions such as crumbly caulking, full gutters, or loose shingles, remove peeling pigment past sanding, cleaning, and priming earlier repainting.

Blistering a.1000.a. Bubbling

iStock

Paint picture show fails to properly adhere and lifts off the surface in the form of multiple rounded bumps. Blisters can appear on both interior and exterior painted surfaces—drywall, plaster, metal, and wood.

What causes paint to cicatrice or bubble?

Oestrus and moisture are both blister gremlins. Painting in direct, intense sunlight or on overly hot surfaces can cause heat bubbles on exteriors; newly dried latex paint that'south exposed to dew, pelting, or loftier humidity may too blister.

On interiors, moisture passing through the walls from bathrooms, kitchens, basements, and laundry rooms can push paint off the surface. Oil-based paint is also apt to blister when applied over a damp surface—or when applied over water-based (latex) paint. Other causes of blistering include painting over a muddy surface, eschewing primer, and improper technique.

Repair and Prevention

Outburst a few bubbles and examine the behind of blistered pigment, as well as the substrate if it becomes exposed, to decide if moisture or estrus is the culprit.

1. If the blisters contain several coats of pigment and popping them reveals bare substrate, there'south a moisture result. Address this by repairing plumbing, replacing caulking, and/or increasing ventilation as required. Then remove all blistered pigment, sand polish, make clean, prime, and repaint.
2. If blisters affect only the previous coat of paint, heat is likely at fault. Remove blisters and the underlying pigment or primer, then sand to smoothen and ho-hum the surface, make clean, prime, and repaint, taking care that the surface is below 90º F.
3. Stir pigment slowly yet briefly with a wooden stirrer or drill attachment. Stirring too chop-chop or for besides long can introduce bubbles to the paint that could transfer to the surface.
4. Exist patient when rolling. If you detect bubbles during application, tedious your stroke speed.
5. Ideally, stick to one formula to avoid baking: latex over latex and oil over oil. While it's possible to successfully apply latex paint over oil-based primers and paints if necessary, you should try to avoid doing then equally it's likely to lead to blistering.

Efflorescence

Crusty white salt crystals may wait appealing on a pretzel, but non on the painted masonry of your dwelling. Efflorescence (besides known as mottling) appears when the salts inherent in brick, concrete, cinderblock, and mortar dissolve in moisture and and so leach out to the surface.

What causes efflorescence?

A multifariousness of factors contribute to efflorescence, including:

• insufficient curing time for cement or mortar during construction;
• moisture migration from inside the house;
• groundwater penetration from an inadequately waterproofed basement;
• insufficient surface prep to remove previous efflorescence; and
• painting over holes, cracks, or unrepaired pointing.

Repair and Prevention

Tackle efflorescence on a warm, dry day. Eliminate excess moisture weather externally past waterproofing and repairing cracks, repointing, and sealing around windows and doors with butyl rubber caulk.

In that location are various ways to remove efflorescence, and yous may demand to use a combination, depending on the extent and severity: a wire brush, scraper, low-pressure level washer, and/or cleaning with diluted white vinegar or a trisodium phosphate (TSP) solution (wear protective gear when working with this chemical) and and then rinsing thoroughly.

Applying an impregnating hydrophobic sealant to a building fabric surface can forestall water absorption and go on moisture from inbound the material. Colorless water repellents may foreclose efflorescence from recurring, as may silicone or acrylic coatings. Allow to dry out completely earlier repainting.

Alligatoring

Perhaps the nigh artistic term for a paint trouble, alligatoring refers to a blueprint that really does resemble reptilian skin. It starts as subtle wrinkling (a.k.a. checking), and then develops into wide rectangular cracks. Alligatoring tends to be more mutual with oil-based paints.

What causes alligatoring?

Paint naturally expands and contracts in response to temperature fluctuations and, over fourth dimension, loss of elasticity tin result in alligatoring.

The process can be hastened through such missteps as applying a rigid coating such as oil enamel over a softer, more flexible glaze (due east.g., latex paint or latex primer); painting over a glossy end (the topcoat non bonding properly to the glossy terminate), or not allowing sufficient dry time between primer/basecoat and topcoat.

Repair and Prevention

1. Remove unsightly scales by scraping, sanding, applying chemical removers, or using a oestrus gun.
2. Then rinse to banish dust and let dry out completely. Prime, allow to dry and repaint.

Chalking

A fine, powdery white substance that forms on painted exteriors, chalking is most oft seen in arid, sunny climates. It tends to exist most visible on pale-colored flat paints and is likely to occur on improperly sealed porous materials and poor-quality, factory-finished aluminum siding.

What causes paint to chalk?

The pigments in paint are naturally released when exposed to weather changes, so some chalking is to exist expected over time. But serious cases are usually due to using the wrong production—either interior pigment or depression-quality outside pigment that contains a high degree of extenders (white, powdery paint additives). Over-thinning paint prior to application can too lead to chalking.

Repair and Prevention

1. Eliminate all evidence of chalking past power washing or treating with TSP solution, and then rinsing.
2. Let to dry thoroughly before repainting with high-quality outside paint.

knickerbockershound.blogspot.com

Source: https://www.thisoldhouse.com/painting/21142799/6-common-paint-problems-how-to-fix-them

Share this post